No Products in the Cart
Car Rear View Monitor
Easy to install and use
High resolution display
Low power consumption
Supports screen rotatable
No audio and input or output
Full color LED backlight display
Stick on your car firmly and stablely
4.3"? LED Backlight Color TFT LCD monitor
It helps to avoid incidents and accidents abrasion well
Support Car DVD, VCD, GPS, camera, STB, satellite receiver, and other video equipment.
Park rear view priority: The monitor will start up automatically, and synchronous display the video from rear view camera when you are backing your car, the monitor will close itself after backing.
Car Rear View Camera
Anti fog glass.
CMOS imaging sensor.
Support NTSC video system.
Snap-in design, it is easy to install.
Embedded mounting in rear bumper.
High sensitivity and low power consumption.
High-definition and 120 degree wide viewing angle.
Water-proof, shock-proof and anti-jamming functions.
It helps to avoid incidents and accidents abrasion well.
Its simple and modest design and small size won??t draw any attention.
This camera can give you a full sight of the back of your car when you are driving.
To protect your car from collision with invisible obstacle, choose a high definition and good quality camera as ours.
Perfect solution to get rid of that poor rear view visibility on your car, boat, trailer, camper, truck or any vehicle hat has no rear-view mirror or poor rear vision.
Connect to any type of monitor with a composite yellow RCA jack for crystal clear resolution mounted inside will fit into most vehicle key holes, no other installation needed.
|Car Rear View Camera|
|Camera Size||(0.87 x 0.83)" / (2.2 x 2.1)cm (L x W)|
|Video Cable Length||236.22" / 6.0m|
|Video Output||1.0Vpp, 75Ohm|
|Length Angle||120 Degree|
|Cable Length of Camera||23.23" / 59cm|
|Scanning System||2:1 Interlace|
|Power Supply Cable Length||16.14" / 41cm|
|Image Reverse||Left-right Mirror|
|High Grade of Waterproofing||IP66|
|Horizontal Resolution||420 TV Lines|
|Effective Pixels||NTSC: 510(H) * 492(V)|
|Current Consumption||No More Than 300mA|
|Image Sensor||CMOS 1/4 MT9V125 or PC1030, Color|
|Minimum Illumination||0.2 Lux/ F1.8(0 Lux with LED)|
|Storage Temperature||-30?? ~ 60??, 95% RH Maximum|
|Operating Temperature||-20?? ~60??, 95% RH Maximum|
|Electronic Shutter||1/50 to 1/100,000 Seconds, 1/60 to 1/100,000 Seconds|
|Car Rear View Monitor|
|Screen Size||4.3 inch|
|Power supply||DC 9V-36V|
|Video input||One way video input|
|Display Component||Color TFT LCD|
|Weight||17.64oz / 500g|
|Dimensions||(8.66 x 8.27 x 1.97)" / (22 x 21 x 5)cm (L x W x H)|
1. Mount the camera inside the keyhole of your vehicle.
2. Adjust the lens of the camera to its best position.
3. Voltage can not exceed 11v.
4. Connect the video output of the camera to the display in your vehicle.
??? Connect the power cord must distinguish between positive and negative (red +, black -) If you pick the wrong, cartridge fuse blows immediately. Please replace the same parameters of cartridge fuse.
??? Two main components both are LCD screen,the surface is glass structure, please note that anti-extrusion.
??? Installation should be solid and reliable, to prevent the situation of falling when the car is brakeing or running and causing personal and equipment accidents.
??? 12v-24V DC contact should be connected to the main power supply in order to prevent excessive voltage affecting the normal use of the machine.
??? The monitor can be connected to a voltage range between 12-36V,but camera could only be connected to 12V,if you wiring with voltage over 12V,the camera may get burnt.Thanks for understanding.